Vigilant vm-1 installation manual

VM-DACT Dual Line Dialer Card provides dialer communications between the VM-1 control panel and remote locations over telephone lines. Alarm, supervisory, and trouble information is transmitted to the remote site using one or two telephone lines in dual or split format to any desired receiver. Datasheet: VM-DACT More of our products from Vigilant Installation GSA-CT1, GSA-CT1HT and GSA-CT2:modules mount to North American 2½ inch(64 mm) deep 1-gang boxes and 1½ inch (38 mm) deep 4 inch square boxes with 1-gang covers and GSA-MP mounting plates. The terminals are suited for #12 to #18 AWG (2.5 mm2to 0.75 mm2) wire size. Application Vigilant VS1 and VS2 Technical Reference Manual Page 215 Form A N.O. 24 VDC at 1 A (resistive load) Environmental Temperature: 0 to 49°C (32 to 120°F) Humidity: 0 to 93% RH, noncondensing Terminal rating All terminals rated for 12 to 18 AWG (0.75 to 2.5 sq. mm) Vigilant VS1 and VS2 Technical Reference Manual FX addressable panel firmware update utility (compatible with panels that have firmware versions 4.0 or later) 04/29/2020. Download. FX-CU Configuration Utility v4.30. FX System Programming utility v4.30. 04/29/2020. Download. FX-CU & FX Panel Firmware v4.30 Release Notes. FX-CU v4.30 and FX panel firmware v4.30 release notes. Acces PDF Ge Vigilant Vs1 Fire Alarm Installation Manual $315.00 + $39.00 Shipping. Est. Delivery Thu, Nov 5 - Mon, Nov 9. 30-day GE Vigilant VS Series Vs1 Main Panel CPU for sale online Note: For a complete list of devices that can be connected to this circuit, refer to the VS Series Compatibility List. The original 1.00, 1.20 and 1.34 versions of firmware have now been replaced with equivalent A versions that can be downloaded into the original PA1011 MX1 Controller or the new PA1081 MX1 Controller. Details on using this program is covered in Section 7.6 of the RDU Mk2 Installation & Programming Manual LT0499. Extract the three files in Product Overview. The VM-DACT Dual Line Dialer Card provides dialer communications between the VM-1 control panel and remote locations over telephone lines. Alarm, supervisory, and trouble information is transmitted to the remote site using one or two telephone lines in dual or split format to any desired receiver. scrambling for the manual as the system counts down to alarm. And for Kidde VS and VM systems. Get the big picture with powerful hardware and software solutions V-SLC2-1 Expander Loop: 250 points (one expansion slot) V-SLC2-2 Expander, Loop 1 of 2: 250 points It also provides 24 VDC for operating ancillary equipment. Voltage 93 to 264 VAC, 50/60 Hz Current Power supply current is included in the total current shown under VM1 above. Current at 120 V, 50/60 Hz 3 A max. Current at 240 V, 50/60 Hz 1.5 A max. Kidde is a UTC brand. 1016 Corporate Park Drive, Mebane, NC 27302 K85005-0134 Wiring diagrams provided herein are for information and reference only and are not to be used for installation purposes. Consult the appropriate installation documents for wiring and configuration details. P/N 46000-1320, Rev. 1.6 Installation Instructions & Owner's Operation Manual for Two to Eight Zone 2400 Series Fire Alarm Control Panels allows for reliable fibered and regulated power to be installed where needed cost effective system expansion provides for genesis and enhanced integrity notification appliance synchronization supports coded output operation self-restoring over current protection multiple