generation g

Echolink baofeng uv 5r manual programming

Echolink baofeng uv 5r manual programming

 

 

ECHOLINK BAOFENG UV 5R MANUAL PROGRAMMING >> DOWNLOAD LINK

 


ECHOLINK BAOFENG UV 5R MANUAL PROGRAMMING >> READ ONLINE

 

 

 

 

 

 

 

 











 

 

Programming software (RSS) for the Baofeng UV-5R series of portable radios Notes: Users have reported that this download is compatible with the indicated Operating Systems but an X does not necessarily mean it isn't. If you have successfully used this D/L with an otherwise un-confirmed O/S please leave a comment. This is done from 'Menu 19' on the UV-5X3 (PTT ID). You can set the S-Code to transmit at either: BOT, EOT, BOTH, or OFF (beginning of transmission, ending of transmission, both, or off). In this example we will set our S-Code to Transmit at 'EOT' (at the end of transmission, (after releasing the PTT)). Comprehensive instruction manual for the Baofeng UV-5R is found Here. About the only way to damage your radio is to transmit (press the side PTT button) with out the antenna connected. Switch between low(2W) and high(4W) power: short press # key. Letter L will show up on the screen. Repeater reverse mode: short press on * key. 5. Select an empty memory position (000 - 127) by using the Up or Down key 6. Press Menu again to store the frequency 7. Press the Exit key to leave the menu. Programming example 2: storing repeater frequencies 1. Switch to VFO A 2. Select VHF or UHF by using the Band key 3. Select the receive frequency you want to store 4. Icom CS-F100S RSS Programming Software. No.5. Kenwood KPG-49D RSS (v4.0) Programming Software. No.6. Yaesu Vertex VX2100/2200 Programming Software. No.7. Kenwood 89D RSS v1.6.0. No.8. Icom RS-BA1 (v2.1) IP Remote Control Software. No.9. Icom IC-F3001 RSS v1.1 Programming Software. No.10. Kenwood KPG 44D RSS Programming Software Turn on the radio, set it to Frequency Mode, and listen to two different ranges of frequencies. 144 mhz to 148 mhz is the 2 meter band, 430 mhz to 450 mhz is the 70 centimeter band. Use the scan feature on your radio by holding down the * key until the voice says "scanning begin" to scroll through the frequencies, and you will eventually hear EchoLink ® software allows licensed Amateur Radio stations to communicate with one another over the Internet, using streaming-audio technology. The program allows worldwide connections to be made between stations, or from computer to station, greatly enhancing Amateur Radio's communications capabilities. There are more than 350,000 validated Handheld Transceiver Tri-Folded Reference Card Condensed setup and operating instructions that simplify radio setup and programming. Simple step-by-step instructions, augmented with hints and explanations. Color-coded, clear and easy to understand instructions, with printing on both sides. Transmit using one of the radios that can access the repeater and use the UV-5R to scan for the CTCSS tone or DCS code that is being transmitted to the repeater. It may be that the tone/code that the repeater requires for access is different from the tone it transmits. Jim KC9HI matty909 Member Joined Mar 19, 2015 Messages 102 Location Programming cable and software - less than $10 - we'd probably get two, just to be on the safe side. External speaker/microphone - $10 - 15 - or otherwise use the included earpiece with each radio. SWR Meter - units are available in the $40 and $60 price range. Easy Programming: More convenient to manual programming most of settings via the keypad, as well as PC programming with the cable in the box. EchoLink Sysop Mode For Node Terminal Operation Multiple Scan Invertible Front Panel; B

Comment

You need to be a member of generation g to add comments!

Join generation g

© 2024   Created by G1013.   Powered by

Badges  |  Report an Issue  |  Terms of Service